|
 |
| Important Informaition for JATCO JF506E | ・ｽ@ | ||||
| Dear sirs, | |||||
| Please be careful for some parts! JF506E design was changed in 2003, | |||||
| which is for Low Reverse Clutch Piston. | |||||
| There are two(2) important Key Points; | ・ｽ@ | ||||
| 1. Please check Friction Plate Quantity 5, 6 or 7 pcs. | |||||
| 2. Please measure Piston Height. | ・ｽ@ | ||||
| The Difference between | PISTON HEIGHT | ||||
| OLD and NEW version. | OLD | NEW | |||
| Friction Plate 5 pcs type | - | CN-10 | |||
| 26.2mm | 23.6mm | ||||
| Friction Plate 6 pcs type | - | CN-11 | |||
| 23.0mm | 20.4mm | ||||
| Friction Plate 7 pcs type | - | CN-12 | |||
| 19.8mm | 17.2mm | ||||
| 1st Steel Plate | CS-09 | CS-10 | |||
| Thickness : 3.8mm | Thickness : 6.4mm | ||||
| The old Piston and 1st Steel Plate(CS-09) are no more produced. | |||||
| If your JF506E is OLD version by checking from Friction Plate Q'ty | |||||
| and the height of Piston, it is necessary to order CN-10/11/12 | |||||
| depending on your JF506E type. | ・ｽ@ | ||||
| Because, CS-09 (3.8mm Thickness) old one is no more available. | |||||
| about Pressure Plate | ・ｽ@ | ・ｽ@ | |||
| Example: for Reverse Clutch | |||||
| 2 pcs. of Steel Plate (2.0mm) are included in SOH/CP kit | |||||
| which are fixed parts, and the thickness should be adjusted | |||||
| by using Pressure Plate. | |||||
| Plate note that Pressure Plate is not in "SOH"series & "CP"series. | |||||
| Please order Pressure Plate separately. | ・ｽ@ | ||||
| Pressure Plate application is listed as follows ; | |||||
| Pressure Plate, Position and Thickness list | |||||
| for Low Clutch | |||||
| CR-01 | Thickness : 3.8mm | All applicatons | |||
| CR-02 | Thickness : 3.9mm | All applicatons | |||
| CR-03 | Thickness : 4.0mm | All applicatons | |||
| CR-04 | Thickness : 4.1mm | All applicatons | |||
| CR-05 | Thickness : 4.2mm | All applicatons | |||
| CR-06 | Thickness : 4.3mm | All applicatons | |||
| CR-07 | Thickness : 4.4mm | All applicatons | |||
| CR-08 | Thickness : 4.5mm | All applicatons | |||
| CR-09 | Thickness : 4.6mm | All applicatons | |||
| for 2th&4th Clutch | |||||
| CR-16 | Thickness : 7.4mm | All applicatons | |||
| CR-17 | Thickness : 7.6mm | All applicatons | |||
| CR-18 | Thickness : 7.8mm | All applicatons | |||
| CR-19 | Thickness : 8.0mm | All applicatons | |||
| CR-20 | Thickness : 8.2mm | All applicatons | |||
| for High Clutch | |||||
| CR-21 | Thickness : 3.4mm | All applicatons | |||
| CR-22 | Thickness : 3.6mm | All applicatons | |||
| CR-23 | Thickness : 3.2mm | All applicatons | |||
| CR-24 | Thickness : 3.0mm | All applicatons | |||
| for Reverse Clutch | |||||
| CR-25 | Thickness : 3.6mm | All applicatons | |||
| CR-26 | Thickness : 3.8mm | All applicatons | |||
| CR-27 | Thickness : 4.0mm | All applicatons | |||
| CR-28 | Thickness : 4.2mm | All applicatons | |||
| for Direct Clutch | |||||
| CR-29 | Thickness : 3.4mm | for VolksWagen | |||
| CR-30 | Thickness : 3.6mm | for VolksWagen | |||
| CR-31 | Thickness : 3.8mm | for VolksWagen | |||
| CR-32 | Thickness : 3.8mm | All applicatons | |||
| CR-33 | Thickness : 4.0mm | All applicatons | |||
| CR-34 | Thickness : 4.2mm | All applicatons | |||
| CR-35 | Thickness : 4.4mm | All applicatons | |||
| CR-36 | Thickness : 4.6mm | All applicatons | |||
| CR-37 | Thickness : 4.8mm | All applicatons | |||
| CR-38 | Thickness : 5.0mm | All applicatons | |||
| for Low&Reverse Brake | |||||
| CR-39 | Thickness : 2.2mm | All applicatons | |||
| CR-40 | Thickness : 2.4mm | All applicatons | |||
| CR-41 | Thickness : 2.6mm | All applicatons | |||
| CR-42 | Thickness : 2.8mm | All applicatons | |||
| CR-43 | Thickness : 3.0mm | All applicatons | |||